Hotline: 0086-752-7839-002

Pre-order! iFlight SucceX Mini-W F7 TwinG Flight Tower System w/500MW VTX

$91.99

PRE-ORDER!The SucceX Min-W F7 TwinG // GYRO FUSION is the NEXT-GEN flight controller you need for your next build. This FC is ready for anything with 4 uarts With its clean intuitive layout, the ..

  • Price in reward points: 92
  • Brands iFlight
  • Product Code: FC07150
  • Availability: In Stock

PRE-ORDER!

The SucceX Min-W F7 TwinG // GYRO FUSION is the NEXT-GEN flight controller you need for your next build.

This FC is ready for anything with 4 uarts With its clean intuitive layout, the SucceX Min-W F7 TwinG makes installation a breeze

with a 4 pin connector for your VTX and an10 pin connector that allows simple plug and play connection with your 4in1 ESC.

But the real magic of this flight controller lies in its TWIN GYRO configuration.

The TwinG uses two identical gyros oriented side by side with one offset 90 degrees from the other. Betaflight uses GYRO FUSION to blend and average the information from both gyros to send a much cleaner signal to the PID loop controller! Less noise and fewer oscillations across the throttle band without adding any delay! Betaflight software filters can be lowered in most cases as well, which brings a significant decrease in delay.

With plenty of processing power and uarts, this is the perfect flight controller for long-range GPS builds. And the TwinG configuration makes it the perfect Fc for builds like macro quads, cinematic filming rigs and x-class racers that are a bit trickier to tune.

TwinG Gyro Setup

-The Betaflight target's default setting is ‘gyro_to_use = both’ / Gyro fusion is active!

-To check the current setting, please use CLI and type ‘get gyro’ to find the responding entry.

-Change the settings with ‘set gyro_to_use = ’ and type ‘save’.

-To get the most reliable performance or encounter noise, oscillation and bent props: Please use the default setting ‘both”. 

-For Single Gyro use, please use the debugging options to find and tune for the cleaner gyro, but lose the dynamic fusion and averaging.

-BF offers the following dual gyro debug options: dual_gyro_raw, dual_gyro, dual_gyro_diff, dual_gyro_combined.

-BlackboxLog explorer graph: dual_gyro_raw Debugging = [0] Roll Gyro1, [1] Pitch Gyro1, [2] Roll Gyro2, [3] Pitch Gyro2.

-The displayed graph will show the Gyro_Raw reading (no filters applied), both gyros can be compared.

SucceX Mini-W F7 TwinG Specifications 

-MCU:216MHz STM32F722

-Gyro:TwinG ICM20689

-Blackbox:32MB

-Betaflight OSD:YES

-Uarts:4

-ESC Telemetry:UART5

-INA Pad:nuart2

-Input voltage:2-6S,MAX 8S

Target:EXF722DUAL

CLI config:IFLIGHTF7_TWIN_G.config

Size:27*27mm /20*20mm φ4 mounting

FC Firmware 

- Betaflight

- Target:EXF722DUAL

Physical 

- Mounting hole:20*20mm,φ4mm with Grommets φ3mm 

-Size:31*31mm 

SucceX Mini-W 40A ESC SPECS:

- MCU: STM32F051

- Current Sensor: Yes

- Input: 2-6s lipo

- Telemetry: Yes

- Installing Hole: 20x20mm, M4

- Target: iFlight-BL32-4IN1

- Constant: 40Amps

- Burst: 45Amps

- Weight:16.7g

- Dimensions: 31*31mm(including the power pads)

- Mounting Holes: 20*20mm,M4

- Supports Dshot1200,Proshot,Oneshot,Multishot 

5.8G VTX SPECS

-Input voltage: 2-6S

-48 standard channels, A/B/E/F/R Band

-Output Power: pit/20/100/200/500mW

-BEC Output: 5V/3A for Camera or FC

-RF Connector: MMCX

-Video Format: NTSC/PAL

-Size: 26*26mm /20*20mm φ4 mounting

Package Included:

-SucceX Mini-W F7 TwinG FC

-SucceX Mini-W 40A  BLHeli_32 4-in-1 ESC

-5.8G 500mW VTX

Write a review

Note: HTML is not translated!
    Bad           Good